Not only the selection of quality components but also their correct handling is crucial for the PV plant's profitability and safety. Therefore, it is essential to know and understand the technical impacts when installing and connecting the various elements.

Avoid Cross-mating of PV Connectors
Avoid Cross-mating of PV Connectors

Article from | Stäubli Electrical Connectors, Inc.

Mating connectors from different manufacturers in a PV system is comparable to installing incalculable technical and legal risks or hidden time bombs.

Not only the selection of quality components but also their correct handling is crucial for the PV plant's profitability and safety. Therefore, it is essential to know and understand the technical impacts when installing and connecting the various elements and to follow the respective regulations.

There are no established standards for connector design and technology in the field of photovoltaic, but a quasi-standard is set with the connector type MC4 from Stäubli (formerly under the name of Multi-Contact). Thus, several manufacturers claim to produce “Stäubli compatible”, "MC4 pluggable", "MC4 connectable“ components. We strongly support the local directives as well as international standards that prohibit the coupling of connectors of different manufacturers. Doing cross-connection is not permitted under any circumstances and may lead to severe damages. 

Our own experience with many incidents over more than 20 years, and, above all,  third-party studies like SolarBankability, the IEA PVPS report on “Quantification of Technical Risks in PV Power Systems”, a study of a group of international scientists or the statement of TUV Rheinland, state unequivocally that cross-mating of different connector brands increases the technical but also the legal risk of a PV system enormously. In addition, this often results in connector failures, power loss, and safety hazards. At worst, this damage may even lead to a fire. Such problems consequently have a negative impact on the return on investment (ROI) and the cost of electricity (LCOE).

Even if the plug face matches when connected, the contact technology on the inside would not match.

Connectors of a particular manufacturer have their individual plug-in face and different contact technology inside, material composition for the contact and insulating parts, and different production processes whereof the exact specifications only being known to the manufacturer.

Factors that are causing technical incompatibility:

  • Deficient technology and product material
  • Differences in the production process and quality standards
  • No aligned tolerance zones to ensure tightness as well as sufficiently high contact forces 
  • No chemical compatibility of all raw materials (including production and auxiliary materials)
  • Changes of the production process without respecting possible interactions
  • Disrespect for the fact that certification and standards are given for one product from one specific manufacturer; those are not manufacturer-independent

 

Consequences of cross-connections

Risks and Consequences of Cross-Connecting

If connectors of different manufacturers are combined with one another, the connection might not be safe. Cross-mating of connectors can cause cracks, leakage, and increased contact resistance of the connection system. What may not be visible from the outside can cause severe damage to the connection and even to the entire system.

By miss-mating or cross-connecting, you easily create a source of risk, which entails not only technical consequences, as already mentioned but also legal ones.

 

FMEA Rating of PV Module Failures by TÜV Rheinland

Prioritization of various risks, belonging to a certain phase and component, according to their Risk Priority Number (RPN). 

In the FMEA, each identified risk is evaluated for severity (S), occurrence (O) and detectability (D) and rated on a scale from 1 to 10 for each parameter. The RPN is obtained by multiplying those three factors and their given numbers (RPN = S x O x D).

The higher the RPN, the higher the risk and substantial consequences on the PV plant and its profitability.

 

International standards

The legal basis, which excludes cross-connections:

  • Product norms (IEC 62852 (EN62852)) and UL 6703 product norm resp. UL 1703 module norm)
  • Installation norms and local regulations
  • Assembly instructions of the manufacturer

Currently, valid PV standards (IEC 60364-7-712:2017; E343181) state that “male and female connectors […] shall be of the same type from the same manufacturer” and that UL certification for connectors only applies if products from the same product family have been mated.

For quality and safety reasons, Stäubli dissociates itself from cross-connecting components of 3rd party suppliers, being advertised as “MC4 compatible”. We assess the cross-connection of components from different manufacturers as a risk for safe use.

We further disclaim any participation in tests from independent test institutes that are misleading and wrongly indicate compatibility. We also consider the efforts from third-party suppliers to verify their connector product by an independent third-party as “Stäubli/MC4 compatible” to be inappropriate and not beneficial to the PV industry. We have not recognized any products from third-party suppliers as being compatible with the Original MC4 product portfolio and do not intend to do so in the future.

 

No certification

There is no compatibility and no (product) certification for a cross-connection. There are different norms on this topic: Product norm for connectors the IEC 62852 (EN62852). For instance, if a plug connector from manufacturer A is connected with a socket connector from manufacturer B, the certification is not valid anymore. The UL1703 STP Module norm requires module manufacturers to list on their module and assembly instructions the specific manufacturer and model numbers of all allowable PV connectors that the module is UL listed to be mated to. This helps installers and inspectors to rely on very clear instructions on what connectors can be used.

The new edition of IEC 61730-1 will require that the connector type which is installed at the module will be printed on the label allowing the installer to know which connector can be used to connect the module.

The installation norm IEC 62548 specifies that plugs and socket connectors mated together in a PV system shall be of the same type from the same manufacturer to make a connection.

 

The content & opinions in this article are the author’s and do not necessarily represent the views of AltEnergyMag

Comments (0)

This post does not have any comments. Be the first to leave a comment below.


Post A Comment

You must be logged in before you can post a comment. Login now.

Featured Product

U.S. BATTERY RENEWABLE ENERGY SERIES DEEP CYCLE BATTERIES

U.S. BATTERY RENEWABLE ENERGY SERIES DEEP CYCLE BATTERIES

Our RE Series batteries are designed to provide the highest peak capacity, longest cycle life, and greatest reliability for use in industrial or residential renewable energy applications. Renewable Energy Series batteries utilize the company's exclusive XC2™ formulation and Diamond Plate Technology® to create the industry's most efficient battery plates, delivering greater watt-hours per liter and watt-hours per kilogram than any other flooded lead-acid battery in the market. Our Deep Cycle batteries are engineered to work with solar panels as well as other renewable energy applications.